Hangzhou Holin Plastic Machinery Co.,Ltd
Hot Products
Home > News > Content

Trimming Machine Mostly Used For Wood Chamfering

Trimming machine mostly used for wood chamfering, metal trim, strip edging and other motor-type activities of the strong trimming equipment. Also known as chamfering machine. Trimming machine is to use the knife to the edge of the board, you can according to the shape of the edge of the wood will be the edge of the corresponding shape, usually used as a right angle into a rounded round edge, also used for proper polishing operation of wood. Also widely used in construction beams, plates, columns, walls and other reinforcement, decoration, wall installation, bracket, railings, billboards, air conditioning outdoor units, rails, satellite receiver elevator, steel plant installation.

The trimmer is generally operated in one hand, but in order to maintain stability and balance, the other hand can be used to assist. Operation, first grasp the trimming machine (note the blade to avoid injury), and then open the trimming machine switch. Beginners have just started operation, do not start the machine just when the vibration and sound scared, just start the machine operation when there is a certain vibration, we must hold the machine, do not let go, otherwise it will be dangerous.

After the start of the trimmer (be careful not to block the inlet and outlet, pay attention to the inlet do not inhale the sawdust), the machine will quickly reach the normal speed, and then you can insert the cutter into the workpiece. If the trimming operations, then the base of the next work close to the ground, and then slowly to the cutter against the work, this time must hold the machine, so as not to rebound. After the cutter is pressed into the workpiece, it is possible to push the milling. The speed of the push is different depending on the type of work, the depth of the milling, the level of the cutter. If you can not move the feeling, or the motor sound weight, you need to slow down the speed. In the process of advancing, to keep the trimming machine smooth, not tilted, otherwise the milling will not be vertical.

After the milling operation is completed, the trimmer can be lifted vertically so that the milling cutter leaves the workpiece. If you do not lift the trimming machine vertically, there is a danger of interrupting the cutter or breaking the workpiece. If the trimming machine operation, or the use of T-shaped ditch knife, flat feather knife, should first push the right side of the cutter to leave the workpiece, and then lift the trimmer.

Trimming machine lift, you can turn off the trimmer switch, and then the trimming machine square on the table, milling tip must be forward, it will not hurt themselves. If you want to re-use, it is best to unplug the plug, clean up the machine.

Every time you install a woodworking cutter, in the use of trimming machine, have to do zero action! (Beginners are easy to overlook, the length of different milling cutter, milling cutter each insert the depth of the spindle is different, the plane or concave hole will cause the problem of milling depth, Moreover, the best milling machine trimming depth of 3-6MM in general, Deep hole, it must be divided into sections, otherwise it will make the cutter quickly blunt or hurt the machine.

1, the trimming machine erected in the workpiece or flat on the desktop. If the boring hole, then stand in the concave hole.

2, the loose base of the plastic twist, so that the milling cutter end contact with the workpiece or table.

3, tighten the plastic twist.

4, check the fuselage on the scale scale, the data that represents "zero". Each time the data is incremented, the data is incremented.

Note: Before using a trimmer, it is very important to zero.

Milling depth of woodworking trimmer

Trimming machine manufacturers usually according to their manufacturing machine performance, set the milling depth, are generally about 3mm. Some will be relaxed for hardwood 3mm, cork 6mm. We can look through the use of their own trimming machine manual, see how the provisions in the end. And its provisions of the 3mm deep, refers to the use of 6mm shaving straight knife in terms of. For example, to 12mm deep hole, it is necessary to operate four times, starting from 3mm, each increase 3mm until 12mm deep so far.

  • Company Profile
    Holin Plastic Machinery is one of the best CE certification plastic machine manufacturers and suppliers, please feel free to order plastic machine, package machine, package mould of high-quality through our website....
  • Product Category
  • Contact Us
    Address:#386, Tongyun Street, Yuhang District, Hangzhou City, China 311112
    Tel: +86-571-88747709
    Fax: +86-571-88747711
Copyright ©Hangzhou Holin Plastic Machinery Co.,Ltd All rights reserved.